Contents Go

HYUNDAI BNG STEEL

使用导航

钢种的选择 不锈钢的选用要考虑使用环境(气候环境)及使用目的,这样才能发挥不锈钢板的特点。

考虑环境条件的选择标准 不锈钢不仅要考虑气候条件,还要考虑耐腐蚀性能,选择合适的钢种。
Criteria for selection based on environmental conditions
钢种 钢种
农村地区 城市地区 工业区 海岸地区
Indoor environment Light corrosive environment General environment Severest corrosive environment Indoor environment Light corrosive environment General environment Severest corrosive environment Indoor environment Light corrosive environment General environment Severest corrosive environment Indoor environment Light corrosive environment General environment Severest corrosive environment
316 Excessive application Excessive application Excessive application Excessive application Excessive application Excessive application Proper Proper Excessive application Proper Proper Can be used if the frequency of cleaning is high Excessive application Proper Proper Can be used if the frequency of cleaning is high
304 Proper Proper Proper Proper Proper Proper Proper Can be used if the frequency of cleaning is high Proper Can be used if the frequency of cleaning is high Can be used if the frequency of cleaning is high Improper Proper Proper Can be used if the frequency of cleaning is high Improper
430 Improper Proper Can be used if the frequency of cleaning is high Can be used if the frequency of cleaning is high Improper Improper Improper Improper Can be used if the frequency of cleaning is high Improper Improper Improper Can be used if the frequency of cleaning is high Improper Improper Improper
室内环境 轻微的腐蚀环境 普通环境 最严重的腐蚀环境
勉强适用 适用 清洁频率高则可以使用 不适用
根据不同建筑部位的选择标准
Criteria for selection based on parts of building<
环境 农村环境 海岸环境
建筑部位 清洁部位 不作清洁 清洁部位 不作清洁
沉淀类未残留 沉淀类残留 沉淀类未残留 沉淀类残留 沉淀类未残留 沉淀类残留 沉淀类未残留 沉淀类残留
304 Applicable Applicable except that the corrosion-causing materials are condensed Applicable except that the corrosion-causing materials are condensed Not Applicable Not Applicable Not Applicable Not Applicable Not Applicable
316 Applicable Applicable Applicable Not Applicable Applicable Applicable except that the corrosion-causing materials are condensed Not Applicable Not Applicable
高耐蚀 Applicable Applicable Applicable Applicable Applicable Applicable Applicable Applicable
喷涂 Applicable Applicable Applicable Applicable Applicable Applicable Applicable Applicable
可适用 不能适用 可适用,但腐蚀诱发物质浓缩时则不能适用

保管及运输 细心管理,不锈钢的表面不要有划痕、水分和指纹等,这样才能防锈并保持表面的美观。

保管 1. 在清洁干燥且通风良好的仓库以原包装进行保管,但最好上面盖上东西;2. 不能弄湿包括间纸的包装材料,如果淋湿立即撤除,防止表面腐蚀; 3. 覆盖保护膜的材料要避免受到日光直射。

运输 1. 为了保护表面,要使用橡胶或垫木; 2. 为了防止表面出现指纹污染及考虑安全,要戴上手套。

加工及施工 要认真遵守不锈钢的加工及施工方法,才能保证最佳质量。

加工

Criteria for selection based on environmental conditions
切割及延压 建议用等离子或激光来切割,但用气割或电弧切割时,要对母材的热影响部位进行砂轮打磨或根据情况进行热处理。
折弯 一般来说,将厚板沿冷轧方向弯折时,要保持板材厚度的两倍的曲率半径进行弯折;与冷轧方向呈直角时,以板材厚度4倍的曲率半径进行弯折。
拉伸 加工时避免模具摩擦引起的损伤,提高成型性能,要使用耐压或耐热的高级特压油作为润滑材料,加工后要洗涤或研磨来清除干净表面油污。
焊接 用溶剂完全清除表面沾附的锈迹、油污等,使用符合材质要求的焊条。 使用清除焊接Slag、Spatter、氧化物的不锈钢刷,要进行酸洗处理,还需要对焊接部位和热影响部位进行钝化处理。

维护管理 不锈钢要定期做清洁,才能保持本身的美观。

各种环境和部位合适的清洁周期
Environment, proper cleaning cycle per part table
部位 结构 沉积物未残留
农村地区 一般环境 恶劣的环境
雨水暴露部位 沉积物残留 1~2 次/年 1~2 次/年 3~4 次/年
沉积物未残留 2~3 次/年 2~3 次/年 4~5 次/年
雨水未暴露部位、室内 沉积物残留 1~2 次/年 3~4 次/年 4~5 次/年
沉积物未残留 2~3 次/年 4~5 次/年 5~6 次/年
各种表面状态清洁方法
Cleaning method per surface status table
表面状态 清洁方法
指纹 使用酒精或有机溶剂(乙醚、甲苯),用柔软的布擦拭后用水来清洗
脂肪、油、油脂污染 用柔软的布或纸擦拭后用中性洗涤剂氨溶液洗涤
焊接热变色 硝酸溶液(10%)或氢氟酸洗涤后,用氨或重碳氢钠溶液进行中和处理并用水洗涤
因表面污染物质而生锈 使用盐酸、硫酸、硝酸溶液(10%)或研磨洗涤剂清洁
漂白剂及各种酸(Acid) 附着物 立即用水洗涤,泡在氨或重碳氢钠溶液后,用中性洗涤剂或温水洗涤
标签及保护膜 用温水和温和洗涤剂擦拭,黏胶成分使用酒精或有机溶剂
红色Rust 用砂布或不锈钢刷除锈后使用清洁药剂
灰尘 用温和洗涤剂或温水洗涤
碳有机物质 洗涤前用热的中性洗涤剂或氨溶液泡,使用含有少量研磨剂的洗涤剂
彩虹花纹 用温水和中性洗涤剂进行清洁

焊接性能 不锈钢要使用与钢种相配的焊条,才能保持其本身美观的特性。

不锈钢的焊接难易度
Welding table of stainless steel table
焊接方法项目 应用厚度
(mm)
钢种 用途
304 309 310S 410 430
气焊 t<1 2 2 2 2 2 主要用于堆焊
埋弧焊 t>0.8 1 1 1 2 2 主要用于中厚板的对接焊接、边角加固焊接、大直径管道焊接、铸件的补焊等
电弧焊 0.5<t<3 1 1 1 3 3 主要用于薄板的对接焊接、边角加固焊接、小直径管道焊接等
MIG焊接 t>3 1 1 1 3 3 主要用于中厚板的对接焊接、边角加固焊接、大直径管道焊接等
Submerged
arc welding
t>6 1 2 2 3 3 主要用于中厚板的对接焊接、边角加固焊接、PLANT用大型板材的直接焊接等
原子氢焊 0.3<t<3 2 2 2 2 2 对接焊接、边角加固焊接、压力容器焊接等
点焊 0.15<t<3 2 2 2 3 3 主要用于不要求气密性的薄板的搭接焊接、飞机、车辆、厨房用具等
Flash butt
welding
0.25<t 2 2 2 3 4 主要用于对接焊接、飞机、汽车管道、机器零件等
缝焊 0.15<t<2 2 2 2 3 3 主要用于要求气密性的对接焊接、汽车零部件、燃烧器、冷冻用配件、厨房器具等
焊锡焊接
(Soldering)
0.3<t<2 3 3 3 4 4 主要用于薄板焊接,强度不重要且不要求尺寸精度的接合小型零件的焊接
(注)
  1. 1. 最常使用的焊接方法,被广泛使用;
  2. 2. 使用的情况较多,但受到一定限制;
  3. 3. 只在特殊情况下使用;
  4. 4. 几乎不使用。
埋弧焊适用的焊条
Proper welding for covering arc welding table
钢板材质 焊条 KS 规格
STS302, STS304, STS304L D307, D308, D308L, D349, D630
STS309S D309, D309L, D309Nb, D309NbL, D309Mo, D309MoL, D312
STS310S D310, D310Mo
STS316, STS321, STS347 D16-8-2
STS316, STS316L, STS444, STS317, STS317L D316, D316L, D316L1L, D317, D317L, D318
STS309S, STS310S D329J1
STS321, STS347 D347, D347L
STS410, STS430 D410, D410Nb, D430, D430Nb